Critical Process Died Windows 10 Loop || Solved In 2022

Table of Contents

Introduction

Over the years of Windows’ existence, the occasional Blue Screen of Death (BSoD) has persecuted us. STOP mistakes are BSoDs, which can be a part of the Windows operating system.

When a deadly system blunder occurs, those messages appear, with the primary intention of informing the consumer about the reason for the error so that they can figure out viable solutions.

BSoDs are most usually caused by defective memory, overclocking, horrific drivers, corrupted storage, or maybe poorly written software.

The ‘CRITICAL PROCESS DIED‘ error is one such BSoD that often seems while Windows 10 starts up. The critical system died error suggests that a program critical to the operating system’s operation has died because of a problem or error.

The error is followed by the error code ‘0x000000EF’ in older variations of Windows. This code refers to the ‘CRITICAL PROCESS DIED’ error, one of the 500+ regarded BSOD error codes.

In Windows 10, a blue display with the hidden error message “Your PC bumped into a problem and needs to restart” seems while a critical system dies. We’re simply collecting a few error information before restarting for you.

If you need to analyze more, appearance up “CRITICAL PROCESS DIED” on the internet later. Most instances go back to the scary blue display with the identical horrible error while restarting.

Causes

Source: howtogeek.com

Corrupt files in the memory are the primary cause of this error. The corrupted files cause an error during the boot process, corrupting the entire hard disc and resulting in data loss.

The following are the primary causes of the Critical Process Died Windows 10 Error:

System files that have been corrupted.
Malicious files in the memory could be the source of abnormal behavior.
Driver issues may be accompanied by additional hardware flaws.
Issues with compatibility, as well as the installation of advanced software that may or may not be compatible with the hardware.
The disc is corrupted due to bad sectors.
Compatibility issues may arise as a result of bad updates.

Methods To Remove This Error

This is a common problem mentioned in lots of forums and articles, and we have observed a few useful answers to restore it that are indexed below.

1. Safe Mode Should Be Used To Restart The Computer

Source:edu.gcfglobal.org

In general, this error will render your computer or pc unusable, requiring you to restart it. This hassle happens each time you restart the laptop. You can restart the laptop in secure Mode in this case.

This is a quick manner to begin your laptop’s Windows system, and it is able to save you from getting this mistake at some stage in the startup process.

Windows 10 should be restarted.
Before Windows 10 starts loading, press Shift + F8 to force it into restoration mode. You can boot into Safe Mode from the restoration mode.
To start your computer, visit Advanced Boot Options and pick out Safe Mode as the boot mode.

Safe Mode also can be accessed in any other way. Kindly get an installation disc or restart your computer several times to get to WinRE.

Then select Troubleshoot Advanced options Startup Settings Restart from the Troubleshoot menu. You’ll see the screenshot below; press the corresponding key to activate Safe Mode.

2. All Drivers Should Be Upgraded

Source:microsoft.com

After you restart your pc in Safe Mode, test to look if any of your tool drivers have any errors; many blue display screen errors, along with the 0x000000ef error, are a result of hardware or drivers.

Please observe the commands below: By pressing Win + X, you can access Device Manager.

Begin by checking all of your drivers. If you see a yellow exclamation mark next to a driver, it means the driver is broken.

This driver must be uninstalled and reinstalled in this case.

Furthermore, it is viable that after an upgrade, your hardware drivers are no longer supported by your Windows operating system. As a result, all drivers have to be upgraded through right-clicking a motive force and choosing Upgrade Driver Software.

3. Clean Up Your Boots

Source:motherboardgeeks.com

You can carry out a clean boot in Safe Mode if you get a BSOD Critical Process Died Windows 10 error.

Press Win+R and type MSConfig into the Run box to open the System Configuration window. Select Selective startup and Load system services in the System Configuration window.

4. Remove The Most Recent Software

You may also have installed a few virus-infected software programs for your computer.

This error might have been resulting from a virus, so please uninstall any lately installed software program.

Remove the Most Recent Software

5. Return To A Previous State

If the error took place lately, you could restore the system to its preceding state via way of means of the usage of the device repair factor you created.

You can do this in the Windows Recovery Environment by going to the Advanced menu and selecting System Restore.

Frequently Asked Questions

Is Windows 10’s F8 Is A Safe Mode?

Windows 10 doesn’t activate safe Mode by pressing the F8 key, as it did in previous windows versions. Windows 10’s safe Mode and other startup options can be made accessible in a variety of ways.

Why Is It That My Critical Process Continues To Die?

When a critical component of Windows detects that data has been modified when it shouldn’t have been, the Critical process died issue occurs.

This element could be a faulty driver, a memory error, or something else entirely. The majority of the time, this error occurs unexpectedly while users are working on their computers.

Conclusion

The solutions described above should resolve the ‘CRITICAL PROCESS DIED’ error in Windows 10 in 99 percent of cases. In order to troubleshoot your computer, you must first boot into Safe Mode and then Clean Mode.

To fix your system, you may carry out a system restore or use the SFC device to restore corrupted files. In addition, the same methods could be used to fix a variety of other Windows 10 Blue Screen of Death (BSoD) issues.